Dell Vostro 3450 System Board Replacement

ID: 105212

Description: In this guide, we will show you how to remove...

Steps:

1. Slide the left and the right battery release latches to the unlock position.

2. Slide the battery and remove it from the computer.

3. Press the ExpressCard to release it from the computer.

4. Slide the ExpressCard out of the computer.
5. If this is all you are doing Follow Step In Reverse if not Go to Next Step.

6. Press the keyboard down. Pry the keyboard with the use of a flat-head screwdriver towards the display to reveal the first keyboard retainer.

7. Pry up the second keyboard retainer.

8. Pry up the third keyboard retainer.

9. Pry up the fourth keyboard retainer.

10. Pull up the keyboard from the palm rest.

11. Release the latch on the system board connector, then disconnect the keyboard cable.
12. If this is all you are doing Follow Step In Reverse if not Go to Next Step.

13. Loosen the screw that secures the memory door.

14. Pry up the memory door near the screw hole, lift and remove it.
15. If this is all you are doing Follow Step In Reverse if not Go to Next Step.

16. Remove the screw that secures the optical drive to the computer.

17. Gently pry the optical drive out of the computer.

18. Remove the screws that secure the optical drive bracket.

19. Remove the optical drive bracket from the optical drive module.

20. Remove the screws in the battery compartment.

21. Remove the screws in the optical drive compartment.

22. Remove the rubber from the bottom base on the right side.

23. Remove the rubber from the bottom base on the left side.

24. Remove all the screws from the bottom base.

25. Flip the computer around and remove the screws that secures the palm rest.

26. Release the latches on the system board connector, then disconnect the touch pad cable and the finger printer cable.

27. Release the latch on the system board connector and then disconnect the power button cable.

28. Release the latch on the system board connector and then disconnect the hot key cable.

29. Pry up the right side of the palm rest.

30. Pry up the left side of the palm rest.

31. Pry up the sides of the palm rest and remove it from the computer.
32. If this is all you are doing Follow Step In Reverse if not Go to Next Step.

33. Remove the screws that secure the hinge cover.

34. Press down on the hooks highlighted in the image.

35. Flip the computer around and remove the hinge cover from the side.
36. If this is all you are doing Follow Step In Reverse if not Go to Next Step.

37. Remove the screws that secure the display hinge.

38. Loosen the screw that secures the low-voltage differential signaling (LVDS) cable.

39. Disconnect the LVDS cable from the system board.

40. Disconnect the wireless local area network (WLAN) antenna cable.

41. Remove the screws that secure the left hinge.

42. Remove the screws that secure the right hinge.

43. Lift the display assembly and remove it from the computer.
44. If this is all you are doing Follow Step In Reverse if not Go to Next Step.

45. Remove the screw that secures the WLAN card.

46. Pull the WLAN card straight out of its socket and remove it.
47. If this is all you are doing Follow Step In Reverse if not Go to Next Step.

48. Release the latch on the system board and then disconnect the VGA cable.

49. Remove the screw that secures the VGA board.

50. Remove the VGA board from the chassis.
51. If this is all you are doing Follow Step In Reverse if not Go to Next Step.

52. Disconnect the system fan cable from the system board.

53. Remove the screw that secures the system fan.

54. Remove the system fan from the bottom base module.
55. If this is all you are doing Follow Step In Reverse if not Go to Next Step.

56. Disconnect the DC-in cable connector from the system board.

57. Disconnect the speaker cable from the system board.

58. Remove the screws that secures the system board.

59. Disconnect the system board from the Input/Output panel.

60. Lift and remove system board from the chassis.
61. If this is all you are doing Follow Step In Reverse if not Go to Next Step.