Google Pixel 4 Display Assembly Replacement

ID: 136195

Description: This repair guide was authored by the iFixit...

Insert a SIM eject tool, bit, or a straightened paper clip into the small hole on the SIM card tray on the left edge of the phone.
Press firmly to eject the tray.
Remove the SIM card tray.

Prepare an iOpener and apply it to the bottom edge of the back panel for one minute.
A hair dryer, heat gun, or hot plate may also be used, but be careful not to overheat the phone—the display and internal battery are both susceptible to heat damage.

Apply a suction cup to the heated edge of the back panel by pressing down on it to create suction, as close to the edge as possible.
If your back glass is badly cracked, covering it with a layer of clear packing tape may allow the suction cup to adhere. Alternatively, very strong tape may be used instead of the suction cup. If all else fails, you can superglue the suction cup to the broken panel.

Pull up on the suction cup with strong, steady force to create a gap between the back panel and the frame.
Depending on the age of your phone, this may be difficult. If you are having trouble, apply more heat to the edge and try again.
Insert the point of an opening pick into the gap.

Slide the opening pick across the bottom towards the left corner to slice the adhesive.
With the pick still inserted, slide it from the bottom left corner over to the bottom right corner to completely slice the bottom side adhesive.
Leave the pick inserted in the bottom right corner to prevent the adhesive from re-sealing.

Insert a second opening pick underneath the back panel directly over the charge port.
Slide the opening pick to the bottom left corner of the phone.

Slide the opening pick around the bottom left corner and across the left side of the phone to slice the adhesive.
The adhesive can be very gummy. Push the pick in and out in a sawing motion to help with slicing.
Stop when you reach the top left corner, near the camera, and leave the pick inserted.

With the first two opening picks still in place, insert a third pick on the lower part of the righthand side.
Slide the opening pick up towards the top of the phone, slicing the right side's adhesive.
Stop when you reach the top right corner, and leave the pick inserted.

Slide the third opening pick around the top right corner and across the top side of the phone, slicing the final strip of adhesive.

Once you have sliced around the perimeter of the phone, carefully lift the right edge of the back cover, opening it like a book.
Do not try to pull the panel all the way off yet, as it is still connected to the phone.

Continue swinging open the back panel until you can rest it on the left edge the phone, being careful not to put any stress on the attached ribbon cable.
During reassembly, this is a good point to power on your phone and test all functions before re-sealing the back panel. Be sure to power your phone back down completely before you continue working.

Remove the five T3 Torx screws securing the battery connector shield:
Four 4.0 mm screws
One 2.1 mm screw
Throughout this repair, keep track of each screw and make sure it goes back exactly where it came from.

Whenever you use the spudger near the battery, be very careful not to puncture the battery.
Using the pointed end of a spudger, pry the battery connector straight up from the motherboard to disconnect the battery.
To re-attach press connectors like this one, carefully align and press down on one side until it clicks into place, then repeat on the other side. Do not press down on the middle. If the connector is misaligned, the pins can bend, causing permanent damage.

Using the flat end of a spudger, gently fold the battery cable over so it doesn't accidentally make contact during the rest of your repairs.

Use a T3 Torx driver to remove the two 4 mm screws securing the back panel connector cover.

Using the pointed end of a spudger, pry up and disconnect the back panel connector.

Remove the back panel.
During reassembly, follow this guide to install custom-cut adhesives for your device.
Follow this guide if you are using a pre-cut adhesive card.

Use a T3 Torx driver to remove the four 4 mm screws securing the camera connector cover.

Using a pair of tweezers, tilt the camera cover up and slide it out of the retaining slot on the upper right corner of the phone to remove.

Using the pointed end of a spudger, pry the camera and sensor connectors straight up from the motherboard.

Use a T3 Torx driver to remove the two 2.4 mm screws securing the front camera and sensor assembly.

Prepare an iOpener and apply it to the right edge of the display for one minute.

This process will almost always destroy the OLED display panel. Only proceed if you are replacing an already-broken display assembly.
Apply a suction cup to the heated edge of the display assembly
If your display is badly cracked, covering it with a layer of clear packing tape may allow the suction cup to adhere. Alternatively, very strong tape may be used instead of the suction cup. If all else fails, you can superglue the suction cup to the broken display assembly.
Pull up on the suction cup with strong, steady force to create a gap between the display assembly and the frame.
Depending on the age of your phone, this may be difficult. If you are having trouble, apply heat to the edge and try again.
Insert the point of an opening pick into the gap.
Depending on the age of your phone, this may take significant force. If you are having trouble, apply more heat and try again.

Slide the opening pick down the right bezel of the phone, between the display and the frame, to slice the adhesive.
Leave the pick inserted in the bottom right corner.

Insert a second opening pick underneath the display assembly in the top left corner of the phone, near the front-facing camera cutout.
If this is difficult, you may need to reapply an iOpener to the upper edge of the display assembly.
Slide the opening pick around the corner and down the left side of the phone, stopping about halfway down, and leave the pick inserted.

Insert a third opening pick under the display assembly in the middle of the right edge of the phone and twist to separate the assembly.

Tilt the display assembly up along the left edge of the phone.
Slide the display connector out of the hole near the motherboard to separate the display assembly from the rest of the phone.
The connector will slide out without any force.

Remove the display assembly.
You will have to thread the replacement assembly's display cable through the motherboard cutout.
If you're having trouble, you can unclip the white antenna cable running through the same cutout or you can loosen and partially remove the motherboard.
If you're using a custom-cut adhesive, follow this guide for instructions on how to apply adhesive to the replacement display assembly.
Be sure to test your repairs before you affix the display assembly with adhesives.
If you are using Tesa tape to reattach the display assembly, follow this guide.
During the boot-up process after reassembly, the display assembly will go through a calibration sequence. Do not touch the assembly during this process, as it could result in improper touch calibration and create touch issues.

Back