Mitsubishi Hands Free Module Firmware Update (AM/FM-ST Electronic Tuning Radio, CD Player, DY-1MU3R45-T and DY-1MU3R45-T-2)

ID: 162788

Description: This guide provides step-by-step instructions...

Steps:

  1. Turn the Ignition switch to the ACC or ON position.
  2. Switch off the radio and CD player by py pressing on the PWR/VOL knob.
    3. Step image
  3. Press the following buttons in that order within sixty seconds from Step 1:
  4. The 1 RPT button.
  5. The ⏮ button.
  6. The ⏭ button.
  7. The 4 ⏩ button.
  8. The display should now read DIAG MODE.
  9. When an invalid button is pressed during diagnosis mode except the hands free-ECU update, the diagnosis mode will be cancelled, thus switching off the radio and CD player.
  10. While in diagnosis mode, the sound input to the microphone unit is output directly through the speaker.
    11. Step image
  11. Turn the ♪/SEL knob clockwise to display HFM DIAG.
  12. Press on the ♪/SEL knob to display HFM DIAG TOP.
    13. Step image
  13. Turn the ♪/SEL knob clockwise twice to display the Parts Number.
  14. The display should read something along the lines of PN XXXXXXXX.
  15. We'll need this later when downloading the Firmware file.
    16. Step image Step image
  16. Turn the ♪/SEL knob clockwise twice to display the Software Version.
  17. The display should read something along the lines of S/W XXXXXXX.
  18. If the Version Number is 19.00.000 you already have the last available Firmware installed and don't need to do anything.
    19. Step image Step image
  19. You can download the firmware files here: Version 19.0.0 (Europe) and Version 19.0.0 (Japan and North America).
  20. Check if the Firmware Version works with your device.
  21. Download the Firmware for your device.
  22. Press on SHOW ALL.
  23. Download update.package.
    24. Step image Step image
  24. The flash drive needs to be formatted to FAT32 and should not be larger than 16GB. Additionally the head unit can be a bit picky and might not accept all flash drives. If it can't read your flash drive, just try a different one.
  25. Copy the update.package file to the root directory of the USB flash drive.
    26. Step image
  26. Insert the USB flash drive into one of the USB ports in your car.
  27. You can usually find a USB port inside the center console or below the head unit.
    28. Step image
  28. Re-enter the HFM DIAG-Section of the Diagonstic Menu by repeating the previous steps or pressing the 6 ↩ button while displaying the Version Number.
  29. Initiate the Update by pressing on the ♪/SEL knob.
  30. If the display reads NO FILE it means that it couldn't read your flash drive.
  31. If the display reads HFM UPDATE it means that it found an update file on your flash drive, and will proceed in 3 seconds.
    32. Step image Step image
  32. When the display reads CODE_, enter the Security PIN using the number buttons.
  33. If you don't have one set you can just enter 1234.
  34. Perform the following steps to remove your Security PIN, if you have forgotten it:
  35. Return to HFM DIAG TOP by long pressing the 6 ↩ button.
  36. Forecefully remove on the Security PIN by long pressing the the ♪/SEL knob until the display reads UNLOCK.
  37. The display will return to HFM DIAG TOP after 3 seconds. You can now proceed by repeating Step 9.
    38. Step image Step image
  38. The update will start 3 seconds after you entered the correct Security PIN.
  39. Wait for the update to finish.
  40. Do not remove the flash drive or turn off the car while the update is running!
  41. Once the update is completed the display will read UPDATE COMPLETE.
Back