Samsung Galaxy S25 Ultra Earpiece Speaker Replacement

ID: 204788

Description: Follow this guide to replace the earpiece...

Let your Galaxy's battery drain below 25% before starting this repair—a charged lithium‑ion battery may catch fire if damaged.
Unplug all cables from your phone.
Completely power off your phone by holding the side key and volume down button and selecting Power off.

Glass shards can complicate disassembly—or worse, cause injury. If your phone's back glass is cracked, follow this step.
Apply strips of packing tape to the cracked glass until it's completely covered—this will help keep the glass contained and allow the suction cup to stick.
Make sure there's a single strip (not overlapping) of tape across the bottom edge, big enough for a suction cup to fit on.
Only cover the glass itself—don't stick any tape to the frame.
Consider wearing safety glasses to protect your eyes from any glass shaken free during the repair.

Adhesive secures the back cover to the frame. Heating the cover softens the adhesive, making it easier to separate.
Heat an iOpener and lay it on the bottom edge of the back cover for two minutes.
Alternatively, you can use a hair dryer or heat gun to heat the cover.
Improper use of a heat gun can destroy the display and/or battery—follow the linked instructions carefully.

While the back cover heats, note the following about its adhesive:
The cover is secured with adhesive around the perimeter of the frame. Use this picture as a reference while you separate the adhesive.
Only insert your tool slightly under the cover near the cameras to avoid damaging them.

Apply a suction handle to the center of the back cover's bottom edge, as close to the edge as possible.

Pull up on the suction handle with strong, steady force until a gap forms between the back glass and frame.
Use the fingers of your lifting hand to hold the phone down, or steady the frame with your free hand—be careful, your phone may be hot.
Insert the tip of an opening pick into the gap.

If the back cover feels stuck at any point when separating the adhesive, apply heat to the area and try again.
Slide the opening pick along the bottom edge to separate the adhesive.

Slide the opening pick around the bottom right corner and up the right edge to separate the adhesive.

In the next two steps, only insert the pick slightly (a few millimeters) near the cameras to avoid damaging them.
Slide the opening pick around the top right corner and along the top edge to separate the adhesive.

Slide the opening pick around the top left corner and down the left edge to separate the adhesive.

Use the suction handle to lift and remove the back cover.
If the cover still feels stuck, go back around the perimeter with an opening pick and separate any remaining adhesive.
During reassembly:
This is a good point to power on your phone and test all functions before sealing it up. Be sure to power your phone back down completely before you continue working.
Check your rear cameras for any smudges and gently wipe them with a clean, lint–free cloth if necessary.
Your replacement back cover adhesive will be applied to either the frame or the back cover. Use cutouts and contours to see where it lines up best. If it matches the back cover, follow this guide. If it matches the frame, use this guide.

Use the point of a spudger to pry up and disconnect the wireless charging coil press connector.

Throughout this repair, keep track of each screw and make sure it goes back exactly where it came from to avoid damaging your phone.
Use a Phillips screwdriver to remove the ten screws securing the wireless charging and loudspeaker assembly:
Four 3.5 mm‑long screws securing the wireless charging coil
Six 3.5 mm‑long screws securing the loudspeaker

Two tabs on the right side of the wireless charging coil are secured with mild adhesive.
Heat an iOpener and lay it on the tabs for one minute to soften the adhesive.

During the next two steps, be very careful not to puncture or dent the battery, as it can leak dangerous chemicals or catch fire. Don’t use sharp or metal tools.
The tabs are very fragile. If it feels like they may tear, apply more heat and try again.
Gently slide the point of a spudger under the top edge of the upper tab and lift slowly to separate it.
You may need to do this a few times before the tab fully separates.

Repeat the previous step to separate the lower tab, starting at the bottom edge.

Use the point of a spudger to pry up the right side of the loudspeaker and unclip it.
During reassembly, press firmly around the perimeter of the loudspeaker to engage its clips.

Every press connector has a corresponding gold arrow on the board that shows the proper location to pry—nifty! Prying at the wrong location risks damaging the fragile surface‑mounted components on the board.
Use the point of a spudger to pry up and disconnect the battery press connector.

Use the point of a spudger to pry up and disconnect the earpiece speaker press connector (the uppermost, short one) from the top right of the motherboard.

Use a Phillips screwdriver to remove the five 3.5 mm‑long screws securing the earpiece speaker.

Use the point of a spudger to lift the earpiece speaker by its top left corner until it unclips.
Be careful not to scratch the cameras with your tool.
Remove the speaker.
During reassembly, press firmly around the perimeter of the speaker to engage its clips.
Be careful not to smudge the cameras or press on surface-mounted components.

Back