Canon EOS Rebel T2i Dioptric Adjustment Lens Replacement

ID: 40741

Description:

Steps:

  1. Before beginning, ensure that the camera is off, and the battery is removed.
  2. Pry open the rubber I/F terminal cap with your finger.
  3. Remove the two M1.7x2.5mm JIS #000 screws that are underneath the I/F terminal cap.
  4. Using a plastic pick, or another thin plastic prying tool, pop off the I/F terminal cover from the camera.
    5. Step image Step image Step image
  5. On the left side of the camera, remove the following screw:
  6. One M1.7x6.0mm JIS #000 screw
  7. On the right side, remove the following screws:
  8. One M1.7x5.5mm JIS #000 screw
  9. One M1.7x3.5mm JIS #000 screw
    10. Step image Step image
  10. Remove the battery door.
  11. Open the battery door to about a 35° angle.
  12. Pull the battery door straight outwards.
  13. Remove the following screws from the bottom of the camera:
  14. One M1.7x6.0mm JIS #000 screw
  15. Two M1.7x2.5mm JIS #000 screws
  16. One M1.7x5.5mm JIS #000 screw
    17. Step image Step image
  17. Slide the viewfinder eyepiece vertically upwards.
  18. Start to pull the back cover partially off of the camera.
  19. Use caution when removing the back cover, there is a ribbon cable that connects the LCD screen to the main PCB board.
  20. Disconnect the LCD screen ribbon cable from the main PCB board.
  21. Use a plastic spudger to lift up the black locking tab.
  22. Carefully pull out the ribbon cable from its connector using a pair of angled tweezers.
  23. Finish pulling the back cover off of the camera body.
    24. Step image Step image Step image
  24. Remove the following screws from the front of the camera:
  25. Two M1.7x5.5mm JIS #000 screws
  26. On the bottom of the camera, remove the following screws:
  27. Three M1.7x5.5mm JIS #000 screws
    28. Step image Step image
  28. Slide a spudger tool towards the tripod mount, underneath the plastic cover.
  29. Push the plastic cover up and over the tripod mount.
  30. Pull the front cover off of the camera.
  31. Electric Shock Warning: With the front cover off, the high voltage capacitor on the DC PCB board is now exposed. It is recommended that you use a capacitor discharge tool to ensure the capacitor is fully discharged before proceeding further.
    32. Step image Step image Step image
  32. Remove the screws next to the viewfinder:
  33. Two M1.7x2.5mm JIS #000 screws
  34. One M2.0x8.9mm JIS #000 diopter screw
  35. Remove the following screws from the top of the camera:
  36. One M1.7x2.5mm JIS #000 screw
  37. One M1.7x5.0mm Phillips #000 screw
    38. Step image Step image
  38. Disconnect the microphone cable from the main PCB board.
  39. Position a flathead 2.5mm screwdriver between the main PCB board connector and the microphone connector.
  40. Gently wiggle the flathead screwdriver back and forth until the microphone connector comes free.
  41. If you do not have a flathead 2.5mm screwdriver, another similarly sized flathead screwdriver should work.
    42. Step image Step image
  42. Locate the ribbon cable which connects the top cover the main PCB board.
  43. Use a plastic spudger tool to carefully pry off the connector.
  44. Use caution when handling ribbon connectors and their connectors.
  45. Take note of where this fiber optic cable connects to the main PCB board.
  46. The cable will slide out of the connector when you pull the top cover off. You will need to remember to slide this cable back into the connector with a pair of tweezers when reinstalling the top cover. This cable is crucial for the function of the camera flash.
    47. Step image Step image Step image
  47. Disconnect these two cables connected to the DC PCB board.
  48. Use the same method as with removing the microphone cable, except with using a flathead 3.0mm screwdriver.
  49. Gently wiggle the flathead screwdriver back and forth until the connectors comes free.
  50. If you do not have a flathead 3.0mm screwdriver, another slightly larger flathead screwdriver should work.
  51. Gently lift the top cover up and off of the camera body, being careful that the loose cables do not snag on anything.
    52. Step image Step image
  52. Remove the red wire that travels across the mirror box.
    53. Step image Step image
  53. Remove the following screws holding the mirror box in place:
  54. Four M1.7x4.5mm Phillips #000 screws
    55. Step image
  55. Remove three JIS #000 screws to disconnect the ribbon mount assembly
    56. Step image
  56. Now that the top assembly is free, this exposes another screw on the right side of the mirror box.
  57. Remove the following screw:
  58. One M2.0x4.3mm JIS #000 screw
  59. Remove the orange ribbon cable.
    60. Step image Step image
  60. Remove the viewfinder assembly from the camera. The screws that hold the eyepiece in place are accessible. Remove these three JIS #000 screws from the rear face of the eyepiece. Two screws are located at the bottom and one screw is located on top.
    61. Step image
  61. With the screws removed, the eyepiece can easily be pulled free.
    62. Step image Step image
  62. Swivel the dioptric lens 90 degrees.
    63. Step image
  63. Remove pin with tweezers.
    64. Step image
  64. Compress spring and remove spring and dioptric lens assembly
    65. Step image
Back