How to Fix the Hotpoint and Indesit Washing Machine F05 Error Code

ID: 218493

Description: [youtubevideo|0_gst8RokRo]Use this guide to...

Steps:

1. Treat the F05 code as a drainage fault when the washer stops mid-cycle, stays full of water, or doesn't pump water to the drain.
2. A blockage is more likely if the pump area made a loud noise before the machine stopped.
3. Some Hotpoint models use F05 for a pressure switch fault instead of a pump blockage.
4. If the machine drains normally after the filter is clear but F05 returns, investigate a pressure switch fault.
5. Unplug the washing machine from power supply power before opening the filter area or touching water.
6. Pull the washing machine out only far enough to reach the hoses and front filter area.
7. Do not tug the machine forward because the water supply hose and drain hose can pull loose.
8. Turn off the power supply water supply to the washing machine.
9. Inspect the drain hose for kinks or blockages.
10. Look into the wall drain or waste pipe and make sure it isn't blocked.
11. A blocked drain hose or wall drain can cause the same symptoms as a blocked pump filter.
12. Place a large washing bowl near the drain hose.
13. Lower the drain hose into the bowl to drain as much water as possible.
14. Empty the bowl as it fills and keep draining until the flow slows.
15. Expect a lot of water if the machine stopped mid-cycle.
16. Use a large flat blade screwdriver to pry off the lower front cover.
17. Locate the pump filter behind the lower front cover.
18. Lean the washing machine back carefully and slide an empty washing bowl under the pump filter.
19. A washing machine is heavy, so get help if you can't control it safely.
20. Unscrew the pump filter by hand about three turns and pull it out.
21. If the filter won't turn easily, use firm hand pressure and wiggle it gently.
22. Rock the washing machine slightly if debris is jamming the filter.
23. A stuck filter is a strong sign that something is caught inside.
24. Remove any debris trapped in the pump filter.
25. Reach into the filter opening and feel for objects against the pump propeller at the back.
26. Remove coins, hair clips, and other objects from the chamber.
27. Wear protective gloves if you need to reach into the pump chamber because trapped objects can be sharp.
28. Small fingers can make this easier because the access is tight.
29. Check pockets before washing to keep loose items out of the pump.
30. Lean the washing machine forward carefully to drain the remaining water into the bowl.
31. Wait until water stops running from the filter opening.
32. Keep emptying the bowl because a mid-cycle stop can leave a lot of water in the machine.
33. Screw the pump filter back in by hand until it is fully tight.
34. Confirm the filter turns easily after the blockage is removed.
35. Leave the lower front cover off until the leak test is complete.
36. Put the drain hose back into the drain pipe.
37. Clip the drain hose into the U-bend bracket at the top.
38. Turn the power supply water supply back on.
39. The washer may show an H2O error if the water supply is left off.
40. Continue the interrupted cycle or start a new cycle.
41. Use a rinse cycle to check whether the drain pump still works.
42. On this Hotpoint Aquarius model, the rinse cycle was cycle A and took 36 minutes.
43. Leave the washer pulled out and the lower cover off during the test.
44. Watch the pump filter and rear pipes for leaks while the machine fills and rinses.
45. Check that water drains from the waste pipe during the drain portion of the rinse.
46. Listen for loud noises around the pump filter.
47. A loud pump noise before the F05 fault can be caused by an object hitting the pump propeller.
48. If the washer still doesn't drain after clearing the filter and drain path, stop using it and inspect the pump or pressure switch fault.
49. Clean the pump filter about once a year, even if the washer is draining normally.
50. Stop the cycle and clean the filter if you hear unusual noise near the pump filter.
51. Cleaning the filter early can help prevent pump damage.
52. Push the washing machine back into position when the rinse test drains correctly and no leaks appear.
53. Keep the water supply hose and drain hose straight as you move the machine.
54. Clip the lower front cover back into place.